What Is a Shipping Label? What it must show, which size to print, and how to fix one that comes out cut off
A label is read by a scanner far more often than by a person. Pickup, origin hub, line-haul, destination hub, the delivery rider's app: every one of them beeps the same barcode. Get that barcode clean and in one piece and the rest of the label is mostly for you and your buyer.
Quick Answer
A shipping label is the sticker on a parcel with the courier's AWB barcode, the delivery address and pincode, the payment mode (COD amount or PREPAID) and your return address. In India the standard size is 4 × 6 inches on a thermal printer. On ShipSeth you can print it only after the courier booking is confirmed.
What is a shipping label, and how is it different from an AWB or an invoice?
The label is the physical sticker; the AWB is the number printed on it; the invoice is the tax document for the sale.
People use the three words loosely and it causes real mix-ups. When a buyer says "send me the label", they nearly always want the AWB so they can track. When a courier support agent asks for the label, they want the AWB too. Only the packer and the pickup executive care about the sticker itself. Lose or tear a label and the AWB doesn't change: open the same order and print it again, and the same barcode comes out. The AWB guide lays out every number a shipment carries, and the one-paragraph definition sits in the shipping glossary. The Hindi version of this guide is शिपिंग लेबल क्या होता है.
Two more sheets often get printed from the same order list and confused with it. The manifest lists every AWB handed over in a pickup and gets signed by the pickup executive. The packing slip or invoice goes inside the box. Neither replaces the label.
What must be on a courier shipping label?
Five blocks belong to the courier and can't be switched off. Everything else is optional.
| Block | What it carries | What goes wrong without it |
|---|---|---|
| Courier header | The courier's name and logo | The pickup executive of one courier leaves your parcel for another courier's van |
| Payment | COD with the amount to collect, or PREPAID | The rider collects the wrong amount, or nothing, and the doorstep argument becomes an NDR |
| AWB barcode | The AWB as a linear barcode, with the digits printed underneath | Nothing scans, so the parcel sits at the first hub until someone keys it in by hand |
| Deliver to | Buyer's name, address, phone, and the pincode in large type | Mis-sorts to the wrong delivery centre |
| Return to | Your name, address and phone, under "If undelivered, return to" | An RTO parcel has nowhere to come back to |
A ShipSeth 4 × 6 label also prints the box dimensions and dead weight, the order total, the e-way bill number when there is one, your GSTIN and a smaller order-ID barcode. On a B2B carton it adds a DataMatrix and LRN strip for cargo networks. That label still doesn't stand in for the lorry receipt, which travels as its own document (see the LR guide).
When can I print a shipping label on ShipSeth?
Only after the courier accepts the booking and the AWB is issued, which is when the shipment reaches Waybill Generated.
Press Print Label on a draft and ShipSeth refuses with "Label cannot be generated until the shipment is booked with a courier". That block is on purpose. A draft has no AWB, and a barcode carrying an invented number fails at the first scan, which is worse than having no label at all because the parcel physically leaves your godown. For a whole day's dispatch, print in a batch: anything not yet booked is skipped with its reason and every booked order lands in one PDF.
Which label size should I use: 4 × 6, A4 or A6?
Use 4 × 6 if you own a 4-inch thermal printer, A4 if you don't, and anything else only if you already have that roll.
| Size in ShipSeth | Printer | Use it when |
|---|---|---|
| 4 × 6 in (default) | 4-inch thermal | Almost always. It is what couriers and marketplaces expect. |
| A4 page | Any office inkjet or laser | You ship a handful a day, or want the label and a GST table on one sheet |
| A6 (105 × 148 mm) | Thermal or A6 sheets | You already buy A6 stock; it is a few mm wider and shorter than 4 × 6 |
| 6 × 8 in | 6-inch thermal | Big cartons where you want a large, product-heavy label |
| 4 × 4.5 in | 4-inch thermal | Small boxes where 6 inches overhangs the face |
| 2 × 3, 2 × 4, 3 × 2, 4 × 2, 4 × 2.5 in | Narrow or landscape rolls | Only for rolls you are stuck with. Small type and a thin barcode fail first on a dusty hub scanner |
If your print is coming out clipped at the edge, don't change the size to fix it. Size is about the sticker you load. Clipping is alignment, and that has its own settings, covered next.
Why is my shipping label printing cut off or off-centre?
Because the print is landing a few millimetres to one side of the sticker, and ShipSeth's Label Print Setup can move it back.
ShipSeth labels print with a black border, which makes this easy to measure. Take one printed label and a steel ruler. On each side, measure the white gap between the sticker's edge and the border, in mm. If the border is missing on a side, tick "cut off" for that side instead. The tool turns those four gaps into the Horizontal and Vertical offsets to type in at Settings → Labels → Label Print Setup, under Print Calibration. A positive Horizontal moves the print right and a positive Vertical moves it down; both run from −10 to +10 mm, and the same values apply to classic and Label Studio designs.
White gap from sticker edge to printed border
Set Horizontal to
-3.0 mm
Set Vertical to
+1.5 mm
Outer margins (T / R / B / L)
1.5 / 1.5 / 1.5 / 1.5
Moves the print 3.0 mm left and 1.5 mm down.
Label Print Setup · 4 × 6 in (standard thermal) · Horizontal -3.0 mm · Vertical +1.5 mm · Margins T 1.5 R 1.5 B 1.5 L 1.5 mmNothing you type here leaves your browser. Save the new values, print one test label, and measure once more; a second pass usually lands within half a millimetre.
Example, made-up numbers. A 4 × 6 label with both offsets at 0 comes out of the printer with a 7 mm gap on the left, 1 mm on the right, 2 mm at the top and 5 mm at the bottom.
Horizontal: 0 + (1 − 7) ÷ 2 = −3 mm · Vertical: 0 + (5 − 2) ÷ 2 = +1.5 mm
The print is sitting 3 mm too far right and 1.5 mm too high. Set Horizontal to −3 and Vertical to +1.5, and the gaps even out at 4 mm left and right and 3.5 mm top and bottom. Those are the default numbers in the tool above, so you can see the result before entering your own.
Don't drop the outer margins to zero to squeeze more onto the sticker. Every printer has a thin strip along the edge it can't print on, and the 1.5 mm default is there to keep the border out of it.
How many labels does a multi-box shipment need?
One for every box, each carrying that box's own child AWB.
A multi-piece booking has one master AWB for the consignment and a child AWB per carton. ShipSeth prints a separate label per carton marked "Box 1 of 4", "Box 2 of 4" and so on, plus a "Document" label when paperwork travels in its own envelope. The shortcut packers love, printing the first label and photocopying it onto the rest, is the one that loses cartons: the hub sees one barcode, counts one box, and the other three have no record of arriving. How to count cartons at delivery and raise a short delivery is in the multi-piece shipment guide.
Can I hide the buyer's phone number or the order value on the label?
Yes for both; the barcode, addresses and payment block always print.
The classic label settings have a Data Visibility panel with separate switches for Order ID Reference, Receiver Contact Number, Full Return Address, Invoice / Order Value and Item Details. In Label Studio you can mask the buyer's number to something like 97XXXXXX05, and your own number separately. Both masks are off until you turn them on, and the courier's app still has the full number for the rider.
Hide the order value on anything expensive. A ₹15,000 figure printed on a phone box invites attention on its way through four hubs. The COD amount is different: it stays, because the rider needs it at the door.
Which labelling mistakes cause delays, NDRs or weight disputes?
Nearly all of them come down to a barcode that can't be read, or a label that disagrees with the box.
An old label left on a reused carton is the classic. Scanners read whichever barcode they see first, and a parcel can start following the previous shipment's route. Peel it off completely or black out its barcode with a thick marker.
Tape is the next one. Glossy brown tape over the barcode bounces the scanner's light back. Tape only the edges, or use self-adhesive thermal stock and skip the tape.
Then placement: stick the label flat on the largest face, never wrapped round an edge or across a polybag crease, where half the bars fold out of sight.
Finally, the label prints your declared box size and dead weight. If the box you actually packed is bigger, the hub's reweigh will charge the difference to your wallet, and the dispute starts with the label as evidence against you. The weight discrepancy guide covers what happens next. White streaks running through a thermal barcode mean a dirty print head; reprint before pickup, since the AWB doesn't change.
Do Meesho, Flipkart and Amazon orders use a ShipSeth label?
No. Marketplace orders ship on the marketplace's own label, with its tax invoice printed under it.
Those come as A4 PDFs that don't fit a 4 × 6 roll as they are. The free label crop and sort tool cuts them to 4 × 6 or A4 and sorts them by SKU, right in your browser. Orders from your own website, WhatsApp or the shop counter are the ones you book through ShipSeth, and they get a ShipSeth label that can carry your brand. Once they are packed, the pickup and manifest guide covers the hand-over.
Book, label and track from one panel
See the Rate, Book It, Print Your Branded Label
Free to register, no monthly fee. Compare live courier rates before you book and pay per shipment from a prepaid wallet.